Woodstock W1828 Bedienungsanleitung

OWNER'S MANUAL(FOR MODELS MANUFACTURED SINCE 4/11)MODEL W1828 12" DISC SANDERPhone: (360) 734-3482 • Online Technical Support: tech-support@

Model W1828 (For Machines Mfg. Since 4/11)-8-SAFETYAdditional Safety for Disc SandersDISC DIRECTION. Only sand on the downward-moving left side of the

Model W1828 (For Machines Mfg. Since 4/11)-9-ELECTRICALELECTRICALAvailabilityBefore installing the machine, consider the availability and proximity of

Model W1828 (For Machines Mfg. Since 4/11)-10-ELECTRICALGrounding & Plug RequirementsThis machine MUST be grounded. In the event of certain malfun

Model W1828 (For Machines Mfg. Since 4/11)-11-SETUPKeep machine disconnected from power until instructed otherwise.SETUPThis machine has been caref

Model W1828 (For Machines Mfg. Since 4/11)-12-SETUP• Workbench Load: This machine distributes a heavy load in a small footprint. Some workbenches may

Model W1828 (For Machines Mfg. Since 4/11)-13-SETUPWe strongly recommend that you mount your sander to a workbench to prevent it from moving during op

Model W1828 (For Machines Mfg. Since 4/11)-14-SETUPPower ConnectionAfter you have completed all previous setup instructions and circuit requirements,

Model W1828 (For Machines Mfg. Since 4/11)-15-SETUPTest run your machine to make sure it runs properly and is ready for regular operation. The test ru

Model W1828 (For Machines Mfg. Since 4/11)-16-OPERATIONSOPERATIONSGeneralThis machine will perform many types of operations that are beyond the scope

Model W1828 (For Machines Mfg. Since 4/11)-17-OPERATIONSDisabling ON/OFF SwitchFigure 12. Removing switch key from paddle switch.Children or untrain

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, r

Model W1828 (For Machines Mfg. Since 4/11)-18-OPERATIONSChoosing Sandpaper Stock Inspection and RequirementsThe Model W1828 uses a 12" adhesive-b

Model W1828 (For Machines Mfg. Since 4/11)-19-OPERATIONSAttaching SandpaperThe Model W1828 sander uses 12" diameter pressure sensitive adhesive-b

Model W1828 (For Machines Mfg. Since 4/11)-20-OPERATIONSDisc SandingTo use the sanding disc, do these steps:1. DISCONNECT SANDER FROM POWER!2. Set

Model W1828 (For Machines Mfg. Since 4/11)-21-OPERATIONSACCESSORIESDisc Sander AccessoriesThe following Disc Sander accessories may be available throu

Model W1828 (For Machines Mfg. Since 4/11)-22-MAINTENANCEMAINTENANCELubricationSince all bearings are sealed and permanently lubricated, simply leave

Model W1828 (For Machines Mfg. Since 4/11)-23-SERVICESERVICEThis section covers the most common service adjustments or procedures that may need to be

Model W1828 (For Machines Mfg. Since 4/11)-24-SERVICEMiter Gauge CalibrationThe miter gauge should be perpendicular to the face of the disc when it is

Model W1828 (For Machines Mfg. Since 4/11)-25-SERVICETroubleshootingThis section covers the most common problems and corrections with this type of mac

Model W1828 (For Machines Mfg. Since 4/11)-26-PARTSPROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONSandpaper clogs quickly or burns.1. Sandpaper grit is t

Model W1828 (For Machines Mfg. Since 4/11)-27-SERVICEThese pages are current at the time of printing. However, in the spirit of improvement, we may ma

SETUPELECTRICAL MAINTENANCESERVICE PARTSOPERATIONSSAFETYINTRODUCTIONUSE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!ACCESSORIES ...

Model W1828 (For Machines Mfg. Since 4/11)-28-SERVICEON/OFF Switch(viewed from behind)NeutralHotGround110V NEMA 5-15 Plug(As Recommended)StartCapacito

Model W1828 (For Machines Mfg. Since 4/11)-29-PARTS123455-15-25-35-45-566789101112121314151616-11817192021192222-322-222-422-522-123232323232426262527

Model W1828 (For Machines Mfg. Since 4/11)-30-PARTSMain Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION1 X1828001 SHOP FOX LOGO LABEL 22-1 X18

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWoodstock international inc. p.o. box 2309 bellingham, Wa 98227-2309

WARRANTYWoodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years f

High Quality Machines and ToolsWoodstock International, Inc. carries thousands of products designed to meet the needs of today's woodworkers and

Model W1828 (For Machines Mfg. Since 4/11)-2-INTRODUCTIONWoodstock Technical SupportThis machine has been specially designed to provide many years of

Model W1828 (For Machines Mfg. Since 4/11)-3-INTRODUCTIONModel W1828 Machine Specifications, Page 1 of 2MODEL W1828SHOP FOX 12" DISC SANDERMotors

Model W1828 (For Machines Mfg. Since 4/11)-4-INTRODUCTIONModel W1828 Machine Specifications, Page 2 of 2Product DimensionsWeight...

Model W1828 (For Machines Mfg. Since 4/11)-5-INTRODUCTIONControls and FeaturesREAD and understand this entire manual before using this machine. Se

Model W1828 (For Machines Mfg. Since 4/11)-6-SAFETYIndicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate

Model W1828 (For Machines Mfg. Since 4/11)-7-SAFETYAPPROVED OPERATION. Untrained operators can be seriously hurt by machinery. Only allow trained or p