Woodstock W2000 Bedienungsanleitung

COPYRIGHT © 1995 BY WOODSTOCK INTERNATIONAL, INC., REG.# TX 3 360-515 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPEOR FORM WITHOUT

W2000 Rebel® – 9Although the power switch on your router can beturned on and off each time you use The Rebel®, theoptional switch (Item Number W2001)

10 – W2000 Rebel®If using the optional safety switch, make sure it is inthe off position. You can now plug your router into thecord connected to the b

W2000 Rebel® – 11A. Router Table InsertLocated in the four corners of the insert ledge on thetable are four holes. These holes are threaded to accept

12 – W2000 Rebel®For applications where the entire edge of the work-piece is being shaped, the outfeed fence must be offsetby the same amount of mater

W2000 Rebel® – 13Figure 18. Fence alignment.Figure 19. Safety guard adjusted properly.For applications where an adequate bearing surfaceremains after

14 – W2000 Rebel®Figure 20. Miter gauge.Step 6 - Adjust the 90° miter gauge stop bolt so it restsagainst the pin. Re-tighten the jam nut. Becareful n

W2000 Rebel® – 15A. Site Planning B. Working HeightAlthough The Rebel®is completely portable and canbe set up and used just about anywhere, we would

16 – W2000 Rebel®D. General OperationsThe general operating procedures are just that: “gener-al in nature”. They are not the final word on perform-ing

W2000 Rebel® – 17E. Straight Edge ShapingStraight edge shaping requires the use of the fenceassembly. Although many edge shaping router bitshave a gu

18 – W2000 Rebel®G. Freehand WorkThe Rebel®is ideally suited to performing freehandwork. Freehand shaping enables you to profile the edgeof curved or

W2000 Rebel® – 1TABLE OF CONTENTSI. INTRODUCTION ...

W2000 Rebel® – 19Step 6 - Once the workpiece or fixture is contactingthe guide bearing on the router bit, move theworkpiece or fixture away from the

20 – W2000 Rebel®Figure 28. Stop block in position.H. Using Stop BlocksIf a particular application requires that you preciselyand consistently start a

W2000 Rebel® – 21Because there are no moving parts, maintenance is vir-tually eliminated. However, we do make the followingrecommendations:• Give the

22 – W2000 Rebel®VI. Parts Breakdown

W2000 Rebel® – 23VII. Parts List1 TABLE TOP2 LEG3 PANEL4 SIDE PANEL5 CAP SCREW 1/4"-28 X 5/8''7 SETSCREW 10-32 X 5/8''8 FOOT

24 – W2000 Rebel®Woodstock International, Inc. (Woodstock) warrantsthis product against defects in workmanship and mate-rials under normal use and ser

2– W2000 Rebel®For Your Own Safety, Read Instructions Before Using The Rebel®A. Safety Instructions For All ToolsThese safety rules cannot cover every

W2000 Rebel® – 3B. Additional Safety Rules For The Rebel®18. NEVER LEAVE THE TOOL RUNNINGUNATTENDED - TURN POWER OFF. Donot leave the tool until it c

4– W2000 Rebel®Woodstock International, Inc. is proud to offer theW2000 Rebel®Router Table. The Rebel®, namedbecause of its radical design and constru

W2000 Rebel® – 5The Rebel®is designed for heavy-duty use, yet itweighs only 35 pounds and is completely portable.However, when lifting, we must cauti

6– W2000 Rebel®Assembly of The Rebel® is extremely straight forwardand can be accomplished with just a few simple handtools. In fact, the only tools y

W2000 Rebel® – 7Figure 4. Attaching the fence.The Rebel®has a two-part, split fence designed foreither straight-line or offset shaping. Assembling th

8– W2000 Rebel®The safety guard system consists of a clear plasticguard and arm which have been assembled at the fac-tory. There is also a height adju