Woodstock D2796 Bedienungsanleitung PDF herunterladen

INTRODUCTION

When combined with the D2796 Dovetail Jig, these

Woodstock Box Joint Templates allow you to quickly and

accurately produce high quality box joints. Additional tool

requirements include a hand-held router, a guide bushing,

and a straight-cutting router bit. Refer to the table to the

right for specific guide bushing and router bit information.

TECHNIQUE SELECTION

One of three techniques are used when making box joints

with these templates. To determine which technique should

be used, plug the workpiece width measurement into the

formulas below. Note—Whenever possible, cut workpiece

widths so Technique 1 can be used.

Use Technique 1 if:

(Workpiece Width) ÷ (Template Size) = (Even Number)

Example: 4" ÷

⁄2" = 8

This technique is the fastest and simplest for routing box

joints.

Use Technique 2 if:

(Workpiece Width) ÷ (Template Size) = (Odd Number)

Example: 4

⁄2" ÷

⁄2" = 9

This technique requires making and using a spacer board to

rout 1 of the 2 box joint halves.

Use Technique 3 if:

(Workpiece Width) ÷ (Template Size) = (Uneven Number)

Example: 4

⁄4" ÷

⁄2" = 8

⁄2

This technique often results in very thin joint fingers on the

sides of the workpiece. These fingers can break easily dur-

ing routing. Whenever possible, plan workpiece widths so

Technique 1 or 2 can be used.

SET UP

All Techniques

1. Use the chart below to select which router bit and

guide bushing to use.

2. Install the correct router bit and guide bushing on the

router.

3. Adjust the router bit depth according to the formula

below:

(Workpiece Thickness) + (Template Thickness) =

(Correct Router Bit Depth)

4. Prepare a scrap board that is

⁄2" wider and

⁄4" thicker

than the workpiece.

5. Loosen the adjustment bolts on the left-side stops and

adjust them to the far left of the dovetail jig.

6. Place the scrap board under the top clamp with the

front edge flush with the front of the jig. Note—Do not

worry about the precise location at this time.

7. Place the workpiece vertically in the front clamp with

the top edge of the workpiece against the bottom face

of the template. Note—Do not worry about the precise

location at this time.

Template Router Bit Guide Bushing

D3157

⁄2"

⁄2" Straight Bit

⁄8" Guide Bushing

D3158

⁄4"

⁄4" Straight Bit

⁄16" Guide Bushing

D3160

⁄8"

⁄8" Straight Bit

⁄4" Guide Bushing

INSTRUCTION SHEET

D3157

⁄2", D3158

⁄4" & D3160

⁄8"

Box Joint Templates

Read and follow the manufacturer’s instruction

manuals for all power tools used when making box

joints. Serious personal injury could result from fail-

ure to follow this warning.

1 2

Inhaltsverzeichnis

Seite 1 - INSTRUCTION SHEET

INTRODUCTIONWhen combined with the D2796 Dovetail Jig, theseWoodstock Box Joint Templates allow you to quickly andaccurately produce high quality box

Seite 2 - ROUTING BOX JOINTS

All Techniques2. Clamp the workpiece into position.3. Slide the front side stop against the left side of theworkpiece and retighten the adjustment bol

Kommentare zu diesen Handbüchern

Keine Kommentare

Woodstock D2796 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Vernetzung Woodstock D2796 herunter. Manual - Woodstock International, Inc. Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern